Looking for a jointer plane? Here are the best jointer plane reviews you can check out so you get your money’s worth.
If you’re serious about working with wood in your DIY projects, you may be considering adding a jointer plane to your tools. These aren’t really expensive, but then they’re not cheap either. Most people can actually live without one, but if you think you need it then you may as well get the best you can for your money.
Best Jointer Plane Reviews
Taytools 469584 Jointer Plane Review
Many woodworkers just go with this Taytools jointer plane when they need this type of hand plane. It’s very affordable, yet in many ways it’s just as good as the jointers that cost twice as much. It’s made mainly with ductile-cast iron, and this material is virtually indestructible.
The handle and the guidance knob are made from Sapele mahogany, which is tougher than American or African mahogany. It’s better at resisting indentation, it has greater bending strength and stiffness, and it more resistant to shock loads. The Sapele here is premium-grade, and it’s been oiled and hand-rubbed.
The ductile-cast iron frog can be adjusted back or forward. They’ve also used plated cast iron for the lever cap, while you’ve got a single piece of casting for the yoke.
It is 22 inches long overall, and 2⅞ inches wide. It weighs at just 8.3 pounds. The iron is 2⅜ inches wide 0.12-inch thick, and made from tool steel. The bed angle of the iron is 45 degrees. It’s also easy enough to sharpen.
Basically, despite the affordable price what you have here is a monster of a hand plane that will really flatten your wood. It does need a bit of preparation first, so you should clean the oil off from the tool. Make sure the screws are tight, and check the sharpness of the blade. You may need to sharpen the blade first.
The handles are very comfortable to hold, and it’s a solid tool to hold. You can use this not just for sharpening edges, but it can even give your wood a nice surface finish after a swipe or two from this joiner.
Faithfull No.7 Jointing Plane
This one is also quite affordable as well. It’s a No. 7 jointer plane, so it is 22 inches long with the iron 2⅜ inches wide. It’s made from cast iron, while the handle and the guidance knob are made from wood. The machined seating also prevents blade judder and movement. You also have a lever cap with the blade assembly secured by a brass locking screw. It should be easy enough to release the blade when you need to sharpen it.
You may have to take some time to make sure the sole is completely true, but it should be mostly flat to begin with. Inspect the blade as well, and you may have to sharpen it first.
WoodRiver #7 Jointer Plane Review
This is quite expensive, but then again you have premium materials for this jointer. You have a high carbon steel blade, plus fully machined frogs. You also have heavy ductile iron castings. The entire tool weighs 9.5 pounds, and you may find the weight useful when you have to work rather stubborn grain.
The handles are made from Bubinga wood, which is one of the most expensive wood out there. The rear tote has a comfortable shape, and the greater diameter of the blade adjustment wheel makes it easier to advance the blade. You’re able to control the blade better with the lateral adjustment lever and the classic style bearing.
Even the castings have been designed to give you a more solid feel, and you also get better feedback when you use this. All in all, it’s terrific but that price sure can give you pause.
What is a Jointer Plane?
The jointer is a hand plane that can go up to 24 inches long. This is a type of bench plane, and it’s the longest among all the bench planes. Because it’s so long, it’s terrific at perfectly levelling the edges of your wood pieces so you can assemble them side by side. The jointer iron is typically honed straight. This makes it ideal for cutting and shaping perfectly flat edges.
A standard metal jointer has the iron pitched at a 45-degree angle with the bevel down. But you can also opt for a low-angle metal jointer with the iron pitched at just 12 degrees with the bevel up.
Others, however, may go with a wooden jointer. These also have the iron pitched at a 45-degree angle.
The jointer plane may also be referred to as the No.7 plane, when it is 22 inches long and the iron is 2⅜ inches wide. It’s called the No. 8 hand plane when it’s 24 inches long and the iron is 2⅝ inches wide.
Use of a Jointer Plane
This is a hand plane that you use for truing up (in other words, levelling and squaring) the surface or the long edges of your wood boards. It’s also called a “try plane”, but most people call it a jointer because you use it for jointing boards edge-to-edge so you end up with a wider board.
The main purpose of this hand plane is to give your long pieces of wood the totally flat edges you need so that you can joint these boards along their edges. You’ll realize how useful this can be if you want to joint several narrow pieces of wood so that you can end up with a dining table.
Things to Look Before Buying Jointer Planes
What’s it made from? You’ll want something that’s strong and stable. It should have a solid build with minimal movements and blade judder. The blade should also be easy to sharpen.
In general, a longer jointer plane is more effective than a shorter one. It’s for this reason that the jointer plane is the longest among all the bench planes.
Weight consideration is why some people go for the 22-inch version of the jointer plane rather than the longer 24-inch version. The shorter jointer is not as heavy, and therefore easier to deal with.
Comfortable Handles and Guidance Knobs
These should feel great in your hands, so you have better control and you don’t get tired too soon.
Level of Gravity
This is how you notice if the jointer is tipping left or right. You don’t want a very low level of gravity as you may not notice that the jointer is tipping. This is a common problem with bevel-up jointers, which some people like because they’re affordable and easier to use.
Ease of Maintenance
More specifically, you’ll want it easier for you to remove the blade when you need to sharpen it.
Some premium jointers can cost twice as much as a regular jointer, and it’s up to you to consider whether the added features are worth the price increase. Of course, if you have 2 very similar jointers then it’s sensible to just pick the cheaper one.
With the right jointer, you can really increase the number of projects you can do in your woodshop. These jointers can really straighten the edges of your wood for jointing, and it can even give a nice surface finish. If you’re working to build a wooden table, you’ll definitely need the best jointer you can get.